Wiring Schematic diagram

The series of touch switch or touch switch is built by IC NE555, a series of touch switches can be used to turn on lights, alarms or other electronic equipment. This circuit uses 2 pieces of metal plate media as touch, MP1 (Metal Plate 1) and MP2 (Metal Plate 2). Touch switch circuit is equipped with a visual LED indicator for relay status (load active). To enable (Relay ON) can be done by touching the surface of MP1 and to turn it off by touching the surface of the MP2. MP1 and MP2 in touch this switch can use a small piece of copper (diameter 5mm) was enough.

Touch Switch series with NE555.

Power amplifiers that we sometimes raises a raft of small drone as groundingless than perfect.The following are some ways to cope with the hum of the power amplifier: 

1. Keep sensitive circuits of the transformer, casing dimensions are not too small.One blog even suggested to use two-bok, bok special one for the transformer. For the toroid transformer or amplifier with a large transformer, should only contain a series of power amps, with no tone control. 

2. Change the position of the transformer, side by side into the lower side (the transformer is high) withfacing a series of sensitive posts 

3. Use a spacer on each PCB board as high as half the height of the transformer, eg as high as 2.5 cm or more so that the PCB board parallel to the core / center of the transformer, here the effect of the weakest fields. 

4. We recommend using a stereo module instead of two mono modulesThis avoids wiring errors. If forced to, try to sizecable between the right and left modules as long and as short as possible. 

5. Should take the ground path for the speaker of ct ct elco instead of the transformer,if the board pcb mounted two big elco (like elco power supply), takeground path of the speakers here, and check to hear! 

6. Power supply for radio (TX or RX) is very sensitive, use a capacitor4x100nf, 4 pairs of these capacitors in parallel to each mem-diode (bridge). 

7. At the tone control circuit IC op-amp that uses a symmetric power supply,sufficient ground wiring is taken from the signal ground wires only. shouldIC power supply (7812) installed near the main power supply, notmounted near the tone control. 

8. Always use a stereo cable shrouded perfect (color stereo cablered-white-covered ground and wrapped in transparent skin. 

9. For power supply, use capacitors of 2200uF per ampere elco 

10. Zoom and ground wires as short as possible, especially a pair of elco (ct line between elco) power supply (can be tried for the amplifier blazer) 

11. For the amplifier should be mounted to the computer casing when not in the ground soil is diground PC casing soil 

12. Pairs of each kit to the circuit without passing groundnya nut / baud / spacer. Do not let the existing ground line at the hole pcb connected to the casing / box. Do not follow this ground. ground attached to the casing should have one. if necessary use a plastic spacerovercome the noise: 

1. Use the active component (IC) that qualified as TL084, TL074, notLM324. LM324 any brand of noise. TL084 is more guaranteed authentic yellow (ST), not white. For now, the IC TL084 is printed white-work unstable frequencyhigh (treble breaks and more noise). For IC 4558 (NE5532) use plain white silk screening JRC4558D or TL072 - TL082 yellow, LF353 noise. LM741 (NE5534) can be replaced with the Hitachi HA17741, LF351 noise may also, has never been tried.we do not have to look for the brand and the price is more expensive because it is the most low noise. 

2. If necessary, the circuit power amplifier OCL, lowering its gain by lowering the value ofresistor in the path gain from 33k to 22k speaker, mimics the gain-clone lower amplifier noise. 

3. Should simplify the circuit, the circuit is too complex is more susceptible to noise and interference. 

4. Should then potentio / volume mounted on the input-power amplifier, such as professional amplifier without tone control.

The series of Universal PIC Programmer can be used with software IC-Prog 1:05. Universal PIC programmer circuit is very simple with BC337 transistor 1 pieces, 2 pieces of IC regulators 7805 and 7808 as well as some components of passive supporters. Universal PIC Programmer series can be supplied with 2 pieces of 9V batteries. For communication with computer circuit Universal PIC Programmer uses a serial RS232 port of computer. Then for the PIC to be programmed provided 5 lanes for the PIC that is DATA, Clock, Vpp, Vcc and Ground. For more details, can be directly seen in the figure below.

The series of Universal PIC Programmer can be used to program the PIC family of 16F84A series, 12C509, 16C765 and the other. Hopefully this series of Universal PIC Programmer can help for friends who want to make PIC programmer

Amplifier circuit built-up is pretty nice not always complex. There are a series of amplifiers that I saw a picture of the kit immediately. The circuit is quite simple, there was the most complex in the pre-amp and its protector.

How a series of ...Op-amp stage 1 is the heart of the circuit, the input stage with enough power to drive the power transistor. Sensor1 ntc & 2 can be attached to the main heatsink, this is optional so it can be eliminated, its functions to lower the bias voltage value if the heatsink overheating. There is no bias trimpot, R6 and R8 instead divide the voltage so we get <= 0.6v at the base driver tr.

If the voltage is just a little more driver transistors can be damaged and could trigger the final transistor is damaged in congregation / pairs. These transistors are used frequently broken, but after replaced by Sanken, safe. Thus the risk of the snaps without a limiter amplifier.

A pair of Q1 & Q2 transisitor drivers are the main transistor amplifier, while the other three pairs of transistors that form the current dumping circuit mode so it will work if there is a signal (especially bass). Final installation of this transistor is in the Blazer, hercules, Eti300w / new Giant. The design of this kind are designed to produce a stomping bass tones, the clarity about the number two, but here the driver transistor is working at grade A.The heat generated quite a bit because of using this mode (current dumping) plus the number of final / power transistor which is more than one pair. I used to use a minimal amount of the final two pairs of transistors to avoid this summer.

Installation of the load resistor should still be there at the foot of the emitter. R16 and C4 are usually intended to stabilize (reduce) the frequency of ultra treble.All use of Sanken transistors. Supply 63V 800VA toroid ct. Reservois capacitors used for stereo 2x 10.000uF/100VEstimated power ...500W rms at 8 ohms and 1000W at 4 ohms, but supply is limited in the 800VA transformer. Confused with a power output of this? Do not worry about who is more important than that is the loud speaker and the supply has not decreased. With the supply of the transformer between them are quite satisfied to control the speaker says 18 ".If I may be wrong image, R4-220K-C2 in parallel with 68pF