Wiring Schematic diagram: high

Showing posts with label high. Show all posts

Monday, October 27, 2014

TDA7294 High Power Output Amplifier TDA 7294 Diagram Circuit TDA 7294

The famous SGS-THOMSON ST Microelectronics has introduced a Hi-Fi DMOS high-power amplifier circuit TDA7294, its sound great taste bile, which due to its internal circuit from input to output are field-effect devices, rounded sound Mild, delicate Rounuan.

However, with its assembly amplifier, only TDA7294 single-output power is only 70 W, BTL access law is 100 W from top to bottom, do not feel that power cushion. The author several tests, used to promote TDA7294-level, direct-drive one to four pairs of high-power transistor parallel, the output of strong currents, the power output of 400 W (mono), and the circuit is simple and no need to debug that can reliably work Basically, the IC has maintained a sound and performance.

Ruzuo The figure below shows, R6 for the feedback resistor, the author of the value in debugging 22 k Ω more appropriate, R6 also decided this circuit gain, the gain value will increase.

Quiescent current depends on the power of R7, R8, when its value in the following 10 k Ω, the circuit will be in a Group A state of quiescent current adjustable to 100 mA ~ 2A, the author from 30 k Ω, the circuit works in Group B and fairly stable, power of With no radiator, in 2 / 3 the volume, to promote 10-inch speaker and 10 minutes later, the power does not feel that hot, thick sound quite strong.

The author of the trial of the power of T1, T2, had used A1943/C5200, K1530/J201, A1302/C3281, which K1530/J201 the best sound quality, particularly soft Naiting. A map of the parameters, the output power of 200 W, in Group B work, with a small heat sink (I use 14 cm × 5cm × 3cm) to meet their cooling needs. Commissioning of the circuit without a ring box.

Sunday, September 14, 2014

High temperature protector with IC 3584

IC 3584 has thermal protection or voltage automatically shutdown when the temperature at IC exceed 150 degrees or more. You can operate this circuit at the transistor or IC heatsing, if a transistor or IC had exceeded the limit of the heat circuit automatically shutdown.

How to use a thermal shutdown circuit above that is first given a circuit of voltage V+,V-,and ground , the given a voltage Vin to be created automatically shutdown if the temperature is high , and the output is inserted in the circuit of an amplifier or other. Then IC embedded in the heatsing or case, which if too hot will shutdown alone. If the circuit already decided voltage, the voltage will re-connect if the temperature returns to normal.

Friday, September 12, 2014

Simple 4A High Speed Low Side Gate Driver

The UCC27518 and UCC27519 single-channel, high-speed, low-side gate driver device is capable of effectively driving MOSFET and IGBT power switches. Using a design that inherently minimizes shoot-through current, UCC27518 and UCC27519 are capable of sourcing and sinking high, peak-current pulses into capacitive loads offering rail-to-rail drive capability and extremely small propagation delay typically 17 ns.

The UCC27518 and UCC27519 provide 4-A source, 4-A sink (symmetrical drive) peak-drive current capability at VDD = 12 V. The UCC27518 and UCC27519 are designed to operate over a wide VDD range of 4.5 V to 18 V and wide temperature range of -40°C to 140°C. Internal Under Voltage Lockout (UVLO) schemary on VDD pin holds output low outside VDD operating range.

4A High-Speed Low-Side Gate Driver Circuit Diagram

Features

Low-Cost, Gate-Driver Device Offering Superior Replacement of NPN and PNP Discrete Solutions
Pin-to-Pin Compatible With TI’s TPS2828 and the TPS2829
4-A Peak Source and 4-A Peak Sink Symmetrical Drive
Fast Propagation Delays (17-ns typical)
Fast Rise and Fall Times (8-ns and 7-ns typical)
4.5-V to 18-V Single Supply Range
Outputs Held Low During VDD UVLO (ensures glitch free operation at power-up and power-down)
CMOS Input Logic Threshold (function of supply voltage with hysteresis)
Hysteretic Logic Thresholds for High Noise Immunity
EN Pin for Enable Function (allowed to be no connect)
Output Held Low when Input Pins are Floating
Input Pin Absolute Maximum Voltage Levels Not Restricted by VDD Pin Bias Supply Voltage
Operating Temperature Range of -40°C to 140°C
5-Pin DBV Package (SOT-23)

Device Uses

Switch-Mode Power Supplies
DC-to-DC Converters
Companion Gate Driver Devices for Digital Power Controllers
Solar Power, Motor Control, UPS
Gate Driver for Emerging Wide Band-Gap Power Devices (such as GaN)

Wednesday, September 10, 2014

High voltage inverter circuit diagram

This inverter circuit works with a transistor and transformer and other components to increase the voltage becomes high. Input supply voltage ranging from 3V to 6V DC, later it was raised to high voltage AC. However, in this inverter circuit output current is very small, probably under 0.1A even smaller. However, its use you can apply it on a fluorescent lamp 10W maximum power only, and that too takes time to switch on fluorescent lamps.

Tuesday, September 2, 2014

High voltage inverter circuit diagram

This inverter circuit works with a transistor and transformer and other components to increase the voltage becomes high. Input supply voltage ranging from 3V to 6V DC, later it was raised to high voltage AC. However, in this inverter circuit output current is very small, probably under 0.1A even smaller. However, its use you can apply it on a fluorescent lamp 10W maximum power only, and that too takes time to switch on fluorescent lamps.

Part List
R1 = 4K7
R2 = 2K2
R3 = 330K
C1 = 100nF
C2 = 100nF 275V
C3 = 0.22uF 275V
Q1 = D506
L1 = 100 times winding, with 0.8mm diameter copper wire
L2 = 50 times winding, with 0.8mm diameter copper wire
L3 = 5000 times winding, with 0.4mm diameter copper wire

Friday, August 22, 2014

Battery powered high voltage generator Wiring diagram Schematic

Battery-powered-high-voltage-generator Circuit Diagram . Output voltage great enough to jump a l-inch gap can be obtained from a 12-V power source. A 555 timer IC is connected as an astable multivibrator that produces a narrow negative pulse at pin 3. The pulse turns Ql on for the duration of the time period. The collector of Ql is direct-coupled to tbe base of tbe power transistor Q2, turning it on during the same time period.

The emitter of Q2 is direct -coupled through current limiting resistor R5 to the base of the power transistor. Q3 switches on, producing a minimum resistance between the collector and emitter. The high-current pulse going through tbe primary of high-voltage transformer Tl generates a very high pulse voltage at its secondary output terminal (labeled X). The pulse frequency is determined by tbe values of Rl, R2, and C2. The values given in the parts list were chosen to give the best possible performance when an auto-ignition coil is used for Tl.

Battery-powered-high-voltage-generator Circuit Diagram